Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, AnicaLin
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > AirGraver Networking - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 07-16-2021, 04:16 PM
Rob Meixner Rob Meixner is offline
Steel
 
Join Date: Feb 2018
Location: Jordan, NY
Posts: 19
Default Stippling

I need to learn to stipple. So far my efforts are less than satisfactory. I have a MRTHE stippling template that seems to basically create a sharp point. When I try to stipple, it just gets stuck in the metal and I have to physicaly move it to the next spot. I have tried dulling the point, but it doesn't help. I have stippled for years on silver with a very sharp hard metal point mounted on my Foredom hammer piece. I can draw a line of stipple and it goes very quickly. I could keep using this hammer tool, but it seems to me that I should learn to stipple with my air graver. Can anyone offer some suggestions. Thanks...Rob
Reply With Quote
  #2  
Old 07-16-2021, 04:46 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Stippling

Hi Rob, Set the stroke at a long length and hold the point somewhat light on the surface so that it can bounce. The tungsten piston will be helpful too.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #3  
Old 07-17-2021, 06:49 AM
Sam Welch's Avatar
Sam Welch Sam Welch is offline
Platinum
 
Join Date: Jun 2006
Posts: 708
Default Re: Stippling

I don't use the tungsten piston but otherwise do as Steve suggests. I hold the airgraver like a pencil and then use the thumb of my left hand against my right thumb as added control. I hold the point just above the metal and then lightly make contact. This seems to stop all "digging in" of the point. It is all really just firm control of the tool. Takes some practice but you will get the hang of it.
__________________
Sam Welch A.I.E.

Guns, guitars and old cars
Reply With Quote
  #4  
Old 07-17-2021, 07:44 AM
Rob Meixner Rob Meixner is offline
Steel
 
Join Date: Feb 2018
Location: Jordan, NY
Posts: 19
Default Re: Stippling

Thanks...Rob
Reply With Quote
  #5  
Old 07-17-2021, 07:27 PM
Sam Welch's Avatar
Sam Welch Sam Welch is offline
Platinum
 
Join Date: Jun 2006
Posts: 708
Default Re: Stippling

Rob, let us know if this works for you.
__________________
Sam Welch A.I.E.

Guns, guitars and old cars
Reply With Quote
  #6  
Old 07-18-2021, 07:36 AM
Rob Meixner Rob Meixner is offline
Steel
 
Join Date: Feb 2018
Location: Jordan, NY
Posts: 19
Default Re: Stippling

I followed Steve's advice and it did the trick. I hadn't adjusted the stroke of my airgraver yet and this made the difference. My stipple point is fairly sharp, I am going to experiment with different levels of dullness and shape to see what they do. I have stippled for years with my Foredom hammer piece, but with only one tool. I hope that having control over the shape of the tool will give me some different textures. I am also going to explore how I might be able to use the air graver to move heavy bezel walls (1.0 - 1.5 mm). Right now I use a hammer and various brass and steel punches shaped to match the wall. More when I know it...Rob
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 11:22 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.