Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, Bruno
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Gallery and Show & Tell - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 12-10-2006, 09:51 PM
ghost ghost is offline
Gold
 
Join Date: Apr 2006
Posts: 128
Default steve ram lake knife

steve
on your ram knife
how did you get the blackground that black
thanks jay
Reply With Quote
  #2  
Old 12-11-2006, 08:25 AM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: steve ram lake knife

Hi Jay, The background on the piece was cut out with a dental air drill and stippled. The color is flat black lacquer from Gesswein called "Background Antique" Link The lighting in the picture is the key to having the background and cuts be full black. All the lights were shut off in the room except for a lite sheet above the knife. The idea is to have no stray direct light coming in to light the background or cuts. Steve






Reply With Quote
  #3  
Old 12-11-2006, 10:22 AM
ghost ghost is offline
Gold
 
Join Date: Apr 2006
Posts: 128
Default Re: steve ram lake knife

steve you stippled it with dental bit also
what kind of bit is that
thanks jay
Reply With Quote
  #4  
Old 12-12-2006, 08:32 AM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: steve ram lake knife

Cleaning up the corners in background and stippling of background can be done in the same operation by grinding a dental bur down to a point on a diamond lap. With the burr in the rotary tool, hold it against a turning diamond lap and step on the rotary foot pedal. This will quickly grind the burr to a point. Depending on what is needed, grind it to a narrow or thicker point. Next, hold one finger on the burr so it can not spin and grind a couple of flats at random on the point. Try cutting with it and if it doesn't cut well, place another random flat on the point. Keep doing this until you hit a grind that cuts well. It may take three or four tries, but since the flats are random, it only takes a couple seconds to place another flat on. Most of the time, the shape that seems to cut best is similar to a very tiny flat-head screwdriver. Make them different sizes as needed,: a wider one for cleaning out corners and stippling background, and so forth., and a narrower one to deepen a line for wire inlay and for undercutting. After I clean out a corner of the background with the bur I'll back out of the corner making dots/marks with it. Similar motion to making dots with a pen or pencil. The background hard to get to spots can be cut out and the background stippled at the same time this way. I believe Jim Small is using the same method of grinding down burs to a smaller cutter too. It can make faster work of background and stippling. :thumbsup:

Steve
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 08:07 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.