Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,630. Welcome to our newest member, McajCarol
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old Yesterday, 12:44 PM
EdwardBinninger EdwardBinninger is offline
Copper
 
Join Date: Feb 2021
Location: Wisconsin
Posts: 6
Default Angle the graver while cutting and depth of cut

Hi Steve, thanks for constructing such an excellent instrument! When I first connected the classic palm control to my silent air compressor I could feel it passively idling in my hand -it reminded me of my Harley! It truly is a one of a kind amazingly constructed and engineered piece of equipment. The tiny engraving that you did on it keeps giving me inspiration.

My question is: When I watch you use the universal patented tip I notice that you slightly angle the graver to the left (even when making straight cuts). Is this the best way to cut with this graver or were you trying to get a different effect?

Second question: I understand that maintaining a constant depth of cut is a balance as you said like riding a bike.. so I understand the importance of uniform depth when cutting (unless a specific effect is desired) . However, as a new engraver, I am unsure how deep I should be engraving? My wife used to do some hand-engraving and she commented that my engraving appeared quite “deep”. To elaborate, when you guys are engraving lettering is it just barely scratching the surface? Or should there be an ideal depth of cut I am trying to achieve? If my initial cuts are too shallow, will the piece turn out ok if I go over the cut multiple times to increase the depth?

Thanks in advance! Ed
Reply With Quote
  #2  
Old Yesterday, 05:38 PM
Axl Axl is offline
Steel
 
Join Date: Mar 2015
Location: cuba
Posts: 54
Default Re: Angle the graver while cutting and depth of cut

Quote:
Originally Posted by EdwardBinninger View Post
Hi Steve, thanks for constructing such an excellent instrument! When I first connected the classic palm control to my silent air compressor I could feel it passively idling in my hand -it reminded me of my Harley! It truly is a one of a kind amazingly constructed and engineered piece of equipment. The tiny engraving that you did on it keeps giving me inspiration.

My question is: When I watch you use the universal patented tip I notice that you slightly angle the graver to the left (even when making straight cuts). Is this the best way to cut with this graver or were you trying to get a different effect?

Second question: I understand that maintaining a constant depth of cut is a balance as you said like riding a bike.. so I understand the importance of uniform depth when cutting (unless a specific effect is desired) . However, as a new engraver, I am unsure how deep I should be engraving? My wife used to do some hand-engraving and she commented that my engraving appeared quite “deep”. To elaborate, when you guys are engraving lettering is it just barely scratching the surface? Or should there be an ideal depth of cut I am trying to achieve? If my initial cuts are too shallow, will the piece turn out ok if I go over the cut multiple times to increase the depth?

Thanks in advance! Ed
Well I'm not Steve but maybe I can answer some of your concerns, I had the same some time ago. However, I hope Steve responds to them and if I am wrong I will learn then. I think the graver tilt that you mention even in straight cuts is the shooting angle of the camera that Steve used to shoot the videos. The depth of the cuts can be whatever you want but normally they are not that deep, what happens is that in the videos the chips and cuts are huge, resulting from the zoom of cameras or microscopes in the case of trinoculars. Are you using any scope? If not, you may be suffering a bad move from your brain trying to cut as deep as you see in the videos that it really is not that deep. You can also do multiple passes until you reach the depth you want. I think there are some engravers that sell castings of their engravings, this can help you see the real depth that they use.
Reply With Quote
  #3  
Old Yesterday, 06:49 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,481
Default Re: Angle the graver while cutting and depth of cut

Hi Ed and Axl!

Ed, My straight up I tend to lean a little to the left. Not meaning to, but I know I do.
With how deep for like lettering, I'll go whatever is needed to get the width I'm after in that part of the letter. Look at the logo/lettering on the body of the handpiece. That is what the cuts look like.

There are several ways to cut lettering. You can do small outlines around it and several cuts to take out the middle. That is light and shallow. Another way is I usually have one light line and then a larger laid/flared-over cut that becomes the middle and other side at a depth needed to get that width.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 05:53 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.