Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, Bruno
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 07-08-2021, 02:37 PM
EdwardBinninger EdwardBinninger is offline
Steel
 
Join Date: Feb 2021
Location: Wisconsin
Posts: 13
Default What is an ideal way to make fine sketches on metal?

Hey guys, just wondering if any of you have a solution to make sketches directly on metal for engraving.. For example, when i attempt to sketch on a coin under the microscope the 0.5 HB mechanical pencil lead seems far to large and i smooth it into a finer point with sandpaper but the sketch doesn’t show up on the coin..

My goal is to be able to make very fine sketches under the microscope free-hand on metal:

What is the best way to sketch on metal? Graphite, charcoal, pencil lead, some kind of modified extra-fine point sharpie?

Thanks in advance!
Reply With Quote
  #2  
Old 07-09-2021, 12:56 PM
ArtisticAttributes ArtisticAttributes is offline
Gold
 
Join Date: Nov 2007
Posts: 127
Default Re: What is an ideal way to make fine sketches on metal?

I use a very fine layer of office whiteout solution and pencil most of the time for my nickel carvings, but a carbide scriber pen also works well too. It scratches just enough to see but not enough to remove with very little effort if needed.
Reply With Quote
  #3  
Old 07-11-2021, 02:35 PM
Sam Welch's Avatar
Sam Welch Sam Welch is offline
Platinum
 
Join Date: Jun 2006
Posts: 708
Default Re: What is an ideal way to make fine sketches on metal?

Ditto the scribe. I polish the metal to a well worn 600 grit surface to get rid of marks than VERY lightly scribe the design into the metal. Corrections are easy to make by burnishing out the "offending" line and redrawing.

With well polished metal and good lighting a very fine line is easily seen. I use an optivisor instead of 'scope but that should not make a difference.
__________________
Sam Welch A.I.E.

Guns, guitars and old cars
Reply With Quote
  #4  
Old 07-12-2021, 01:22 PM
Wilfred Valtakis II Wilfred Valtakis II is offline
Copper
 
Join Date: Mar 2019
Location: United States
Posts: 4
Default Re: What is an ideal way to make fine sketches on metal?

20210203_205938.jpg
Reply With Quote
  #5  
Old 08-24-2021, 12:21 PM
Damien Connolly Damien Connolly is offline
Steel
 
Join Date: May 2010
Location: Andover, Vermont
Posts: 42
Default Re: What is an ideal way to make fine sketches on metal?

Degrease it a little, and spray with white, flat, acrylic primer. I use Krylon. This enables unlimited drawing and erasing, under the microscope, with the fine point pencils you mention. A fairly light coat, and I scribe/engrave right through the paint. It works!
Reply With Quote
  #6  
Old 08-24-2021, 01:26 PM
chujybear chujybear is offline
Platinum
 
Join Date: Jul 2009
Posts: 740
Default Re: What is an ideal way to make fine sketches on metal?

I feel your pain. That .5 lead looks like an oar under magnification. Even a .2 lead is way too big. I have a few tactics that I employ. The one is probably not that helpful, but it is just accepting the imprecise nature of marking implements and making all final corrections with the graver when I’m putting the lines in.
The other answe is to mark only to your line. That way when you refine with a scrubber, you are not looking to the centre of your lead but one edge of it.

Last one is to mark your centre line with a pen or a sharpie and then when you scribe you are cutting through the black and your line is nice and clear.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 04:01 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.